How to add an M.2 SSD to a PS5
You need one tool for this job: a #1 Phillips screwdriver. Add the drive itself and that's the whole parts list. Sony built a spare M.2 slot into every PS5, and its official installation guide[1] walks owners through using it, so this is a documented upgrade rather than a teardown. Most of the risk sits in buying the wrong drive or a heatsink that's too tall, so that's where I'd spend your attention.
What you need
- A #1 Phillips screwdriver, ideally with a magnetic tip, since the slot screw is tiny
- An M.2 NVMe SSD that meets Sony's spec (below)
- A heatsink, either built onto the drive or bought separately
- A clear table and a few minutes for the console to cool after you shut it down
Before you start, update the PS5's system software. Sony lists that as the first step in its guide.
The drive spec, in plain terms
As of November 2026, Sony's requirements for the expansion slot are:
- Interface: PCIe Gen4 x4 M.2 NVMe SSD (M key)
- Capacity: 250GB to 8TB
- Sequential read speed: 5,500MB/s or faster recommended
- Lengths that fit: 2230, 2242, 2260, 2280 and 22110
- Width with cooling: Up to 25mm
- Thickness with cooling: Up to 11.25mm total: 8.0mm above the board, 2.45mm below it
- Cooling: Required, such as a heatsink or a heat transfer sheet
The two numbers people miss are the heatsink limits. A chunky desktop heatsink with tall fins will be over 8mm and the slot cover won't close. Look for a drive sold with a low-profile heatsink, or check the listed height of a separate one against the table before you order. Sony accepts double-sided heatsinks but says a single-sided one is easier to install, and I'd take that advice; the 2.45mm under the board doesn't leave much room.
The 5,500MB/s figure matches the internal drive. Sony's 2020 hardware spec sheet[2] lists the launch console's built-in SSD at 825GB with 5.5GB/s of raw read bandwidth. Buying to that number means games installed on the new drive shouldn't load slower than the ones on the internal drive.
How much space to buy
The launch PS5 had that 825GB drive. The slimmer model Sony introduced in late 2023 moved to a 1TB SSD[3], and the PS5 Pro ships with 2TB[4]. Part of each drive is reserved for system software, so the usable figure is lower than the box says.
My rule: if you own a launch or slim console, a 2TB drive is where the upgrade starts to feel worth the money. On a Pro, 1TB is often enough. If drive prices dip during November sales, step up a size rather than paying extra for a speed rating well past 5,500MB/s, which the console won't use.
Installing it, step by step
These follow Sony's guide in the order you'll do them.
- Turn the console fully off (not rest mode), unplug every cable and let it cool down.
- Launch model (CFI-1000 series): remove the base, lay the console with the PlayStation logo facing down, grip the top-left corner of the cover and pull it up and to the right. Slim and Pro (CFI-2000 and CFI-7000 series): remove the cover as Sony's guide shows for your model to reach the expansion slot.
- Unscrew the expansion slot cover and set it aside.
- Remove the small screw from the spacer, then move the spacer to the groove that matches your drive's length (2280 is the most common).
- Hold the drive by its edges, line up the notch with the connector, and push it in at an upward angle until it's fully seated.
- Tilt the drive down flat onto the spacer and fasten it with the screw. Snug is enough; don't crank it.
- Refit the slot cover and the console cover, reconnect the cables and power on.
When the console boots, a formatting guide appears on screen. Follow it. Formatting erases anything already on the drive, so don't use one with files you want to keep.
Putting games on it
The drive works as full game storage. Sony says both PS5 and PS4 games can be played directly from M.2 SSD storage, which is the main reason to choose this upgrade over a USB drive: PS5 games can sit on USB extended storage, but they have to be copied back to the internal drive or the M.2 drive before you can play them.
- To send new downloads to the new drive, go to Settings > Storage > Installation Location.
- To move games you already have, open the Game Library, pick the game, then choose Options > Move Games and Apps.
When to stop and rethink
If the cover won't sit flat, take the drive out and check the heatsink height before forcing anything; it's almost always the fins. If the console doesn't show the formatting prompt, power down, reseat the drive at that upward angle and try again before you assume the drive is faulty. And if a reseated drive still isn't detected, check it against the Gen4 and M-key line in the table, because a drive that fails the spec won't be fixed by a second attempt. At that point the cheap fix is a return to the store, not a new console.
Sources
- Official installation guide playstation.com
- Unveiling new details of PlayStation 5 hardware technical specs blog.playstation.com
- New look for PS5 console this holiday season blog.playstation.com
- Welcome PlayStation 5 Pro the most visually impressive way to play games on PlayStation blog.playstation.com